runpuddrun
Back and Better than EVAR
- Joined
- Jul 7, 2011
- Messages
- 2,762
- Reaction score
- 5
- Location
- Overland Park, Kansas
- Handicap
- GHIN 14.8
I began this build (my first full set build) with Wishon 560MC heads that were used but in great condition thinking that I was just going to do a standard SW build but decided to go all out and build it to MOI. I won't bore you all with that, but here is the basic stats for this. I weighed and sorted everything (ferrules, heads, shafts, grips, epoxy) I added tip and hosel weights to get the weights right. I also built the lengths in .4 increments instead of the normal .5.
I dry-fit everything and measured 3x before I cut or eposied and I used my golf ruler to measure club lengths, air compressor to install grips and cut shafts.
It was a lot of fun, confusing at times, and I learned a lot. The shafts are pullout Nippon 1150gh Pro shafts in Stiff flex, grips are Karma MultiCompound's, heads are Wishon 560MC Forged 5-AW.
I am not completely done with it yet and will update this thread with the pictures after I finish turning down the ferrules, and paintfill the heads.
I will also be building the other 2 wedges and building a set of Wishon 870ti with FST 115's in a week or so and will use this thread for all that are interested. I also built 2 drivers and 1 FW that I will update on here as well.
Without further adieu, the pics...
Heads with original badges removed and paintfill removed:
heads with new badges on:
Nippon shafts weighed and sorted:
Ready to work!
Shafts cut and ready to epoxy and grip:
Ready to grip and glue:
Cavity close-up:
Face close-up:
Grips on and epoxied:
That's all for now. I have other pics of the other wedges and stuff, but I'll wait until I finish them to update the thread.
I dry-fit everything and measured 3x before I cut or eposied and I used my golf ruler to measure club lengths, air compressor to install grips and cut shafts.
It was a lot of fun, confusing at times, and I learned a lot. The shafts are pullout Nippon 1150gh Pro shafts in Stiff flex, grips are Karma MultiCompound's, heads are Wishon 560MC Forged 5-AW.
5 iron | D1.3 | 257.8 | 38 | 0 | 50.8 | 0 | 116 | 41 | 416 |
6 iron | D2 | 264.8 | 37.6 | 0 | 50.6 | 0 | 116 | 41 | 422 |
7 iron | D2.5 | 271.3 | 37.2 | 0 | 50.2 | 0 | 116 | 41 | 427 |
8 iron | D2.9 | 277.8 | 36.8 | 0 | 49.5 | 0 | 116 | 41 | 431 |
9 iron | D2.8 | 286.9 | 36.2 | 0 | 49.5 | 0 | 116 | 41 | 439 |
Pitching Wedge | D3.4 | 292.8 | 35.9 | 0 | 49.3 | 0 | 116 | 41 | 444 |
Gap Wedge | D3.8 | 298.4 | 35.6 | 0 | 48.4 | 0 | 116 | 41 | 448 |
I am not completely done with it yet and will update this thread with the pictures after I finish turning down the ferrules, and paintfill the heads.
I will also be building the other 2 wedges and building a set of Wishon 870ti with FST 115's in a week or so and will use this thread for all that are interested. I also built 2 drivers and 1 FW that I will update on here as well.
Without further adieu, the pics...
Heads with original badges removed and paintfill removed:
heads with new badges on:
Nippon shafts weighed and sorted:
Ready to work!
Shafts cut and ready to epoxy and grip:
Ready to grip and glue:
Cavity close-up:
Face close-up:
Grips on and epoxied:
That's all for now. I have other pics of the other wedges and stuff, but I'll wait until I finish them to update the thread.